according to test requirements such as BS Pt. 2 or ISO This can be expressed in two ways, the Coefficient of Friction µ and the Torque Coefficient (K . ISO FASTENERS – TORQUE/CLAMP FORCE TESTING. DIN EN ISO Fasteners – Torque/clamp force testing (ISO + Amd ) (includes Amendment).
|Published (Last):||8 October 2018|
|PDF File Size:||8.45 Mb|
|ePub File Size:||15.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
In this it is also necessary to take into consideration the geometry iao the fasteners — more precisely, the increase of the thread, its flank diameter and the diameter of the head contact. By repeating the test on a sample of the fasteners, the variation in the torque-tension relationship, can be established for an application.
Please first verify your email before subscribing to alerts. Surfaces often have a major influence on this. Based on this data, the nut factor or total coefficient of friction can be calculated and used to evaluate the effect of various fastener finishes, coatings, lubricants and manufacturing processes.
Coefficients of friction cannot be specified using measurement technology. Eddy current method amplitude sensitive. Nevertheless, coefficients of friction are determined for 1607 parts. Under consideration of the revised version of ISOthis document specifies a modification in the scope in order to make ISO applicable for fasteners with self-locking features. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.
Eddy current method phase sensitive.
Product Validation, Verification and Testing
This is not always easy. With these tests it is also possible to check the quality of the coating in ongoing production. You need to log in before adding standards to the monitoring service. We have no document history for this standard. In practice, there are two ways in which companies deal with this: Cross-cut test for adhesion. You may delete a document from your Alert Profile at any time. If the factor is very high, fasteners need to be tightened with a high torque and the efficiency of the fasteners decreases.
Because if bolts and screws are too loose, components may move. The ISO standard enables different reference base plates or reference washers to be used. The respective complementary partial torque can be identified via subtraction. With these fasteners a washer is threaded onto the blank; the subsequent cold forming in which the thread is rolled into the surface ensures that this washer cannot fall off.
Industrial companies and associations often specify a coefficient of friction window for this. Your Alert Profile lists the documents that will be monitored. Already Subscribed ios this document. On some test benches the partial torque is measured in the thread, in others on the base.
Such data can be used to establish the appropriate torque-angle requirement for the specific fastener and joint. 16074, varying degrees of roughness are possible for both types.
Technical terms can not always be avoided. Pressure water jetting test.
BS EN ISO +A – Fasteners. Torque/clamp force testing
This technique has a distinct advantage because the actual joint and fastener can be tested without compromising the joint stiffness through the introduction of a load cell.
They are identified via torque and clamp force. From a standardisation viewpoint, this dilemma is unresolved.
Simple instrumented fixtures with manual testing and data capture Automated testing isk complex systems with customized control dashboards and reports. Webprint Printed and bound. In this process the fasteners are screwed to their own washer.
If fasteners are lubricated, friction is reduced — this applies both with regard to both external lubrication via grease or wax and integrated lubrication via the addition of a lubricant to the coating. FEA can give virtual insight into the structural integrity of new designs before any capital is spent building parts.
Want to learn more and discuss your project? Torque to Yield Tests MEC can be perform tests on 1607 fastened assemblies to obtain torque-angle graphs and to establish the torque to reach the yield strength of the bolt. These bases may be of low or high hardness, uncoated or galvanised.
Coat thickness and coat thickness measurement. This service is ieo available if you are a URL user where you do not log in with an email address.
Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of 160447 standards required in your work. Not only can FEA show where new parts may have potential issues, it can be used to diagnose failures seen in the field, and also to optimize designs in order to reduce cost. The variety around the jso of corrosion and corrosion protection is also in our glossary at home: However, specialists also take a closer look.